Re-attach the outboard to its new position on the jack plate. Use a car or truck jack to move the engine up or down without removing it from the jack plate. Place a board or some other sturdy base below the jack plate. Place the car jack on the base and, using a sturdy length of wood, approximately 2 feet in length, raise the wood on the car jack until it is flush with the bottom of the engine. Use nylon insert nuts all around. Other types of locking nuts or washers may also work. Bolt the jack plate to your transom using at least two 3/8' bolt for each half of the unit. Locate the upper bolt close to the corner of the aluminum angle so that the motor is unable to pull it away from the boat. Re: Jack Plate Install/motor hoist question I just mounted a 150hp Yamaha motor on my CMC jack plate. The motor has a lifting 'U' shaped bracket under the cowl. I just hooked my cherry picker on the bracket a lifted the motor. You may want to check your motor to see if it too has a lifting bracket. Hello, I bought my boat a few weeks ago, a 1997 Grumman 14' flat bottom side console with a 25 Johnson. First time out I noticed a bit of water spraying up the ouboard, and that the motor seemed to be trimmed kinda high. Lowered the pin and so much water sprayed up the leg that I almost couldn't see the motor. So I figured that it had a long shaft motor on a short shaft transom, noticed that the ventilation plate was a couple of inches below the bottom of the boat, and I ordered the mini-jacker from basspro. It just came in today. I took a tape measure to the motor and boat a few minutes ago and found that it is a 20' transom, it's just that the motor leg is about 22'. A jack plate is a hydraulic device that lifts and lowers a boat's main outboard motor. Raising the motor actually lifts the boat out of the water, enabling it to move faster. You have a 20' motor, if the distance between where the motor sits on the transom and the cavitation plate is 21.5', then mounting your jack plate up 3 inches your cavitation plate will be 1.5' above the bottom of the transom. With a 6' jack plate you should be able to raise your motor 2' more with no problem. I'd like to run the motor as high as practical for speed, effeciency, and running shallow. I expect to need a new prop to get the most out of it, and I just bought a tach and water pressure gauge so I'll know what's going on when tuning the setup. 1: Can I mount the mini-jacker slightly above the transom? Microsoft office word excel 2010 cracked version sony. I'd probably only need an inch or two. 2: Can I mount the motor a little about the top of the jack plate? I figure as long as the clamps are fully on the board it should be ok. I will bolt the motor to the plate as well. 3: What size and type of bolts should I use, and how many? I'm guessing SS. The instructions call for 6 bolts to attach it to the transom, but it seems to me that 4 should be good. How To Install Manual Jack Plate On Boat SeatsBonnier Corporation Privacy Policy This policy was last updated on May 16, 2018. At Bonnier Corporation, your privacy is important to us. This Privacy Policy applies to all of the products, services, and websites offered by Bonnier Corporation and its subsidiaries or affiliated companies (collectively, 'Bonnier'). To better protect your privacy, we provide this notice explaining our privacy practices and the choices you can make about the way your information is collected and used by Bonnier. Bonnier acts as a “data controller” for the purposes of the EU’s General Data Protection Regulation. Bonnier has appointed a Data Protection Officer for you to contact if you have any questions or concerns about Bonnier’s personal data policies or practices. The Data Protection Officer’s contact information is as follows: Jeremy Thompson, General Counsel Bonnier Corporation 460 N. Orlando Ave., Ste. 200 Winter Park, FL 32789 [email protected] If you have any questions about this Privacy Policy, or to check your information to verify, update or correct it, please write to us via e-mail at [email protected], or via postal mail at: Privacy Department Bonnier Corporation 460 N. Orlando Avenue, Suite 200 Winter Park, FL 32789 You may also ask for a summary of the information that we have retained, how we have used it, and to whom it has been disclosed. For your protection, we may require that you authenticate your identity before we provide you with any information. Note: For questions related to your magazine subscription, please visit the respective magazine’s customer service website. An overview of the information that Bonnier may collect You are able to take advantage of many Bonnier products, services, and websites without providing any information that personally identifies you by name, address, or other personally-identifying information. We only collect personally-identifying information when you voluntarily submit it to us. Sometimes, we need personally-identifying information in order to provide you with the products and services that you request. Depending upon the product or service, we may ask you for a variety of personally-identifying information. This might include, for example, your name, address, e-mail address, telephone number, gender, and birth date. We may also ask for other information about you, such as your credit card information (when you are making a purchase), interests, income, or education level. We consider certain identifying information 'sensitive.' This includes your credit card number, income level, or any other information that would normally be considered confidential. Some types of personal information will NEVER be requested or collected, such as information on your race or ethnic origin, political opinions, trade union memberships, religious beliefs, health, sex life, or sexual orientation. You may choose not to provide us with any personally-identifying information. In that case, you can still access and use many portions of our websites; however, you will not be able to access and use those portions of any Bonnier website that require your personal information. Many Bonnier websites include community features, such as online forums and message boards. Information that is posted in these areas becomes public information and the use that any third party makes of this information is beyond our ability to control.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |